INTERNATIONAL STANDARD
THERMOMECHANICALLY STRENGTHENED STEEL FOR REINFORCED CONCRETE STRUCTURES
Technical Terms
GOST 10884-94
Thermomechanically hardened steel bars for reinforced
concrete constructions. Specifications
Date of introduction 1996-01-01
Foreword
1. DEVELOPED TC 120 "Cast iron, steel, rolled "
INTRODUCED by the State Standard of Russia
2. ACCEPTED by the Interstate Council for Standardization, Metrology and Certification (Protocol No. 6-94 dated 10.17.94)
3. By the Decree of the Committee of the Russian Federation for Standardization, Metrology and Certification No. 214 dated April 13, 1995, the interstate standard GOST 10884-94 was put into effect directly as a state standard of the Russian Federation from January 1, 1996
4. REPLACE GOST 10884 -81
1. SCOPE
This standard applies to thermomechanically hardened steel smooth and periodic profile with diameters of 6-40 mm, intended for reinforcement of reinforced concrete structures.
The standard contains certification requirements for thermomechanically hardened reinforcing steel for reinforced concrete structures.
2. REGULATORY LINKS
This standard uses references to the following standards:
GOST 380-88 Carbon steel of ordinary quality. Stamps
GOST 2999-75 Metals and alloys. Vickers hardness test method
GOST 5781-82 Hot-rolled steel for reinforcing reinforced concrete structures. Technical conditions
GOST 7564-73 Steel. General rules for sampling, blanks and samples for mechanical and technological tests
GOST 7565-81 Cast iron, steel and alloys. Sampling method for chemical composition
GOST 7566-81 Rolled products and products of further processing. Rules for acceptance, labeling, packaging, transportation to storage
GOST 10243-75 Steel. Test method and evaluation of macrostructure
GOST 12004-81 Reinforcing steel. Tensile test methods
GOST 12344-88 Alloyed and high-alloyed steels. Methods for determination of carbon
GOST 12345-88 Alloyed and high-alloyed steels. Methods for determination of sulfur
GOST 12346-78 Alloyed and high-alloyed steels. Methods for the determination of silicon
GOST 12347-77 Alloyed and high-alloyed steels. Methods for the determination of phosphorus
GOST 12348-78 Alloyed and high-alloyed steels. Methods for determining manganese
GOST 12350-78. Alloyed and high-alloyed steels. Methods for determining chromium
GOST 12352-81 Alloyed and high-alloyed steels. Methods for the determination of nickel
GOST 12355-78 Alloyed and high-alloyed steels. Methods for the determination of copper
GOST 12356-81 Alloyed and high-alloyed steels. Titanium determination methods
GOST 12357-84 Alloyed and high-alloyed steels. Methods for the determination of aluminum
GOST 12358-82 Alloyed and high-alloyed steels. Methods for the determination of arsenic
GOST 12359-81 Carbon steels, alloyed and high-alloyed. Methods for the determination of nitrogen
GOST 12360-82 Alloyed and high-alloyed steels. Boron determination methods
GOST 14019-80 Methods and alloys. Bending test methods
GOST 14098-91 Welded joints of reinforcement and embedded products of reinforced concrete structures. Types, design and dimensions
GOST 18895-81 Steel. Photoelectric spectral analysis method
3. DEFINITIONS
The following terms are used in this standard:
3.1 Reinforcing steel of periodic profile - rods with evenly spaced on their surface at an angle to the longitudinal axis of the rod transverse protrusions (corrugations) to improve adhesion to concrete.
3.2 Smooth reinforcing steel - round rods with a smooth surface that does not have corrugations to improve adhesion to concrete.
3.3 Strength class - the standardized value of the physical or conditional yield strength of steel established by the standard.
3.4 Angle of inclination of the transverse protrusions - the angle between the transverse protrusions (grooves) and the longitudinal axis of the bar.
3.5 Step of transverse protrusions is the distance between the centers of two successive transverse protrusions, measured parallel to the longitudinal axis of the bar.
3.6 Height of transverse protrusions - the distance from the highest point of the transverse protrusion to the surface of the core of a bar of a periodic profile, measured at right angles to the longitudinal axis of the bar.
3.7 Nominal diameter of periodic profile steel (profile number) - diameter of equal cross-sectional area
